Build A Mortising Jig To Rout A Mortise In Stock of Any Thickness ...
The jig shown allows you to rout a mortise in stock of any thickness. Its adjustable jaws ensure that the mortise will be positioned properly, normally centered in the edge of the board.
Cut the jig top from 3/4-inch plywood; make the piece about 15 inches long and wide enough to accept the thickest stock you expect to mortise. Cut the two jaws from 2-by-4- inch stock, sawing the pieces to the same length as the top. To prepare the top, mark a line down its center, then cut a notch along the line at one end using a router. The notch should be as wide as the template guide you will use with your router bit. (If you are using a top-piloted bit, rather than a non-piloted straight bit with a template guide, size the notch to accommodate the bearing.) The notch should be long enough to accommodate the longest mortise you expect to cut. Next, rout two adjustment slots perpendicular to the centerline. Finally, bore a viewing hole between the two slots. To assemble the jig, screw hanger bolts into the jaws, then fasten the top to the jaws with washers and wing nuts.
To use the jig, outline the mortise on the workpiece and mark a line down its center. Loosen the wing nuts and secure the stock between the jaws so the centerline is aligned with the line on the jig top; make sure the top edge of the workpiece is butted up against the top. Tighten the wing nuts. Align the bit with one end of the outline, then mark reference lines on the jig top along the edge of the router base plate. Repeat to mark lines at the other end of the outline. Rout the mortise, starting the cut with the base plate aligned with the first set of reference lines and stopping it when the plate reaches the second set.
Router Jig To Make Mortises - Bookshelf
Maximize Your Router Skills with Ken Burton
The jig also incorporates adjustable stops to make cutting the mortise to ... The jig is designed to work with a plunge router equipped with an edge guide. ...Wood magazine router tips, jigs & techniques
Six ways to plunge right in To put a plunge router through its paces, ... Build the super-handy Mortising Jig, as shown in the drawing on the left, ...Popular Mechanics Workshop: Router Fundamentals, The Complete Guide
Although there are stand-alone mortising machines, they're expensive. A low-cost alternative is to make a mortising jig for your router (see the sidebar ...Bill Hylton's Ultimate Guide to the Router Table
There are better ways to do the job. The Katie jig can be set up to use on the router ... The upshot is that yes, you can do mortises on the router table, ...Router joinery workshop, common joints, simple setups & clever jigs
WHAT YOU NEED TO KNOW Have the hinges on hand; the jig you'll make is specific ... You can cut these mortises by hand with a chisel, but routing them with a ...Everyday News Directory
How to Make a Mortise With a Router | eHow.co.uk
How to Make a Mortise With a Router. Specific tasks in woodworking can present three or four different ways of doing them. Take the mortise and tenon joint. No doubt ...
Precision Router Dado Jig-Carbide Router Bits | Router Bit ...
Use your router and this exclusive new jig to make precise dado joints quickly and with confidence. Built from a solid piece of aluminum, this guide ...
How To Make a Router Jig | How To Do Things
A router jig is used to put your work piece on when using your router. It is a simple guide or template for your router. Jigs are best used for making repetitive ...
Woodworking Jigs--How To Make Router Jigs?
Router jigs are made from wood and are simple to construct. If you are a woodworker looking to create cuts and designs with a router and you'd like to make a jig ...
Mortise Pal - Precision Mortising Jig and Loose Tenon Joinery ...
A key feature of the jig is its simplicity. Mortise Pal uses interchangeable templates and a template guide bushing to guide your plunge router. ...